CDL Practice Tests: New York State Coil Endorsement
Choose A Section:
Go!Void filler is:
- A structure, device, or another substantial article placed against an article to prevent it from tipping that may also prevent it from shifting.
- A tapered piece of material, thick at one end and thin at the other, used to help keep cargo from moving.
- Material used to fill a void between articles of cargo and the structure of the vehicle that has sufficient strength to prevent movement of the articles of cargo.
- A device placed between the deck of a vehicle and car or between articles of cargo, intended to provide greater friction than exists naturally between these surfaces.
Void Filler:
Material used to fill a void between articles of cargo and the structure of the vehicle that has sufficient strength to prevent movement of the articles of cargo.
A bulkhead is used:
- to protect the cab in the event cargo should shift forward.
- to reinforce blocking.
- to unitize articles and is tensioned and clamped or crimped back upon itself. (same as "Strapping")
- to prevent forward movement of cargo.
Bulkhead:
A vertical barrier across a vehicle to prevent forward movement of cargo.
A single metal coil with eye vertical weighing 6,350 lbs requires tiedowns with a minimum aggregate WLL of:
- 6,350 lbs.
- 10,000 lbs.
- 12,700 lbs.
- 3,175 lbs
The sum of the working load limits from all tiedowns must be at least 50% of the weight of the coils.
What is aggregate working load limit?
- The summation of 50% of the working load limits or restraining capacity of all devices used to secure an article on a vehicle.
- The summation of the working load limits or restraining capacity of all devices used to secure an article on a vehicle.
- 50% of the maximum load that may be applied to a component of a cargo securement system during normal service, usually assigned by the manufacturer of the component.
- The maximum load that may be applied to a component of a cargo securement system during normal service, usually assigned by the manufacturer of the component.
Aggregate Working Load Limit:
The summation of the working load limits or restraining capacity of all devices used to secure an article on a vehicle.
What is the maximum ideal angle for an effective direct tiedown?
- 90 degrees.
- 100 degrees.
- 45 degrees.
- 30 degrees.
A direct tiedown is considered effective against forward and rearward forces if it makes an angle less than 45 degrees when viewed from the side of the vehicle.
A direct tiedown is considered effective against side-to-side forces if it makes an angle less than 45 degrees with the horizontal when viewed from the front or rear of the vehicle.
Cargo that isn't prevented from forward movement, and is 4 feet long and weighs 1,500 lbs requires a minimum of how many tiedowns?
- 1
- 2
- It doesn't matter.
- 4
-
If load is 5ft or shorter, 1,100 lbs or lighter:
Minimum number of tiedowns: 1
-
If load is 5ft or shorter, over 1,100 lbs:
Minimum number of tiedowns: 2
-
If load is more than 5ft but less than 10ft:
Minimum number of tiedowns: 2
A 'hook-lift container' is:
- A reusable, transportable enclosure that is especially designed with integral locking devices that secure it to a container chassis trailer to facilitate the efficient and bulk shipping and transfer of goods by, or between various modes of transport, such as highway, rail, sea, and air.
- A specialized container, primarily used to contain and transport materials in the waste, recycling, construction/demolition, and scrap industries, which are used in conjunction with specialized vehicles, in which the container isloaded and unloaded onto a tilt frame body by an articulating hook-arm.
- A platform or tray on which cargo is placed so that it can be handled as an article. (Same as "Skid")
- A vehicle especially built and fitted with locking devices for the transport of intermodal containers.
Hook-lift Container:
A specialized container, primarily used to contain and transport materials in the waste, recycling, construction/demolition, and scrap industries, which are used in conjunction with specialized vehicles, in which the container isloaded and unloaded onto a tilt frame body by an articulating hook-arm.
Working Load Limit (WLL)is defined as:
- The summation of the working load limits or restraining capacity of all devices used to secure an article on a vehicle.
- The depression formed between two cylindrical articles when they are laid with their eyes horizontal and parallel against each other.
- A combination of securing devices which form an assembly that attaches cargo to, or restrains cargo on, a vehicle or trailer, and is attached to anchor point(s).
- The maximum load that may be applied to a component of a cargo securement system during normal service, usually assigned by the manufacturer of the component.
Working Load Limit (WLL):
The maximum load that may be applied to a component of a cargo securement system during normal service, usually assigned by the manufacturer of the component.
Whenever possible, a row of metal coils with eyes vertical requires one direct tiedown to secure against rearward movement at what minimum angle?
- 180 degrees.
- 30 degrees.
- 45 degrees.
- 90 degrees.
At least one direct tiedown against the front of the row of coils, restraining against forward motion, and if practicable, making an angle 45 degrees or less with the floor.
At least one direct tiedown against the rear of the row of coils, restraining against rearward motion, and if practicable, making an angle 45 degrees or less with the floor.
What is the minimum number of tiedowns required through the eye of a metal coil loaded crosswise?
- 1
- As many as possible.
- 2
- 3
Step #2 and #3: Prevent the Coil from Forward and rearward Movement
At least one direct tiedown is required through its eye, restricting forward motion.
At least one direct tiedown is required through its eye, restricting rearward motion.
About The New York State Coil Exam
You must have a New York State coil endorsement if you want to haul metal coils in New York.
Performance Criteria for Securement Systems:
Part I: Cargo Securement Performance Criteria
The standard provides the minimum amount of force that cargo should be expected to withstand, in each direction, as shown below.
These minimum force requirements, called the “performance criteria”, were determined after extensive testing. The securement system MUST be capable of resisting these forces, as shown below.
- The forward force (80% of the cargo weight) represents braking while driving straight ahead.
- The rearward force (50% of the cargo weight) represents vehicle acceleration or braking in reverse.
- The side-to-side or lateral force (50% of the cargo weight) represents traveling on a curve, ramp or changing lanes.
- The vertical force (20% of the cargo weight)) represents cargo vibration during transport. This requirement is satisfied when the cargo is "Fully Contained"
The performance criteria may also be expressed in terms of acceleration, which is shown at right (“g” is the term used for gravity, and represents acceleration or deceleration).
- 0.8 g deceleration in the forward direction.
- 0.5 g deceleration in the rearward direction.
- 0.5 g acceleration in a side-to-side or lateral direction.
- 0.2 g vertical acceleration.
EXAMPLE: If a steel coil weighs 10,000 lbs., the load securement must provide 8,000 lbs. of securement to prevent movement in the forward direction, which is expressed as 80% of the cargo weight (or 0.8 g).
PART II - Performance Criteria for Components of a Securement System
Each component of the cargo securement system should not exceed its Working Load Limit (WLL), when at maximum force. The Working Load Limit is the maximum load that may be applied to a component of a cargo securement system during normal service; it is usually assigned by the manufacturer of the component.
Each force in the performance criteria is to be applied separately to the securement system to determine if it is compliant.
Cargo Securement Terms That Truck Drivers Should Know:
-
Working Load Limit (WLL):
The maximum load that may be applied to a component of a cargo securement system during normal service, usually assigned by the manufacturer of the component.
-
g:
The acceleration due to gravity, 9.823 m/sec2 (32.2 ft/sec2). For cargo securement purposes it is expressed as a percentage of cargo weight, i.e. .5g is 50% of force of gravity or 50% of cargo weight.
-
Contained:
Cargo is contained if it fills a sided vehicle, and every article is in contact with or sufficiently close to a wall or other articles so that it cannot shift or tip if those other articles are also unable to shift or tip.
-
Tiedown:
A combination of securing devices which form an assembly that attaches cargo to, or restrains cargo on, a vehicle or trailer, and is attached to anchor point(s).
Vehicle Structure and Anchor Points
The vehicle must be strong enough to resist the forces in the performance criteria (Section 1). The vehicle must be appropriate for the cargo it is to transport, or it must be adapted to be suitable by using fittings, fixtures, dunnage, cribbing or other means.
Cargo Securement Responsibility
According to federal and state regulations, the carrier and driver are responsible for ensuring that the vehicles, anchor points and other securement components are in good working order, with no obvious signs of damage. The driver is also required to conduct a pre-trip inspection by other operating regulations.
Roadside inspections are conducted in accordance with federal, state and provincial laws. If securement equipment fails inspection, it is likely that the vehicle may be placed out-of-service, and the motor carrier and/or the driver may be fined.
Questions you should be able to answer:
- What is the definition of working load limit?
- What do they call a waterproof sheet used to cover cargo?
- What is a cab shield?
- Whenever possible, a row of metal coils with eyes vertical requires one direct tiedown to secure against rearward movement at what minimum angle?
- What is the minimum angle that indirect tiedowns must form with the vehicle?
- What does "fully contained" means?
- What is blocking used for?
- What is an anchor point?
- What is a friction mat used for?
- Indirect tiedowns create what direction of force?
- How many tiedowns are required for cargo that is prevented from forward movement?
- What is the minimum number of tiedowns required through the eye of a metal coil loaded crosswise?
- What is a bulkhead used for?
- By definition, what is a wedge?
- What is aggregate working load limit?
- What is the maximum ideal angle for an effective direct tiedown?
- In cargo securement, what is bracing?
- What is a rub rail?
- A row of metal coils loaded with eyes lengthwise requires how many direct tiedowns over each side-by-side row or coil?
Why Join Trucking Truth?
- The High Road Training Program
- The High Road Article Series
- The Friendliest Trucker's Forum Ever!
- Email Updates When New Articles Are Posted
Apply For Paid CDL Training Through TruckingTruth
Did you know you can fill out one quick form here on TruckingTruth and apply to several companies at once for paid CDL training? Seriously! The application only takes one minute. You will speak with recruiters today. There is no obligation whatsoever. Learn more and apply here:
TT On Facebook